Showing results: 76 - 90 of 452 items found.
-
Software -
smartGAS Mikrosensorik GmbH
The smartGAS Calibration Tool is a commercial software company that makes it possible to interact with all smartGAS sensors of the EVO series with firmware version 5.17 or higher. With the smartGAS Calibration Tool, it can be read out and the zero point and the end point can be used with a suitable test gas.
-
Labodam
Labodam closed-cup flash point testers are compact, stand-alone solutions which determine the low temperature operability in diesel fuel, biodiesel, blends and gas oils. They are designed as per Test Methods for Flash Point of Petroleum Products (Pensky-Martens Closed Cup Methods).
-
Gardner Bender
Clamp meters test AC/DC voltage, DC voltage, resistance and continuity. Measure conductors at any point in the wire or cable.
-
PA203X-006-009-016-019 -
MISCO Refractometer
Celsius model – The Palm Abbe Glycerine & Propylene Glycol Refractometer is designed to provide the freezing point and percent concentration of both glyercine and propylene glycol antifreeze solutons. This instrument will test glycerine and propylene glycol percent concentration by volume and freezing point in degrees Celsius.
-
PA203X-006-008-016-018 -
MISCO Refractometer
Fahrenheit model – The Palm Abbe Glycerine & Propylene Glycol Refractometer is designed to provide the freezing point and percent concentration of both glycerine and propylene glycol antifreeze solutions. This instrument will test glycerine and propylene glycol percent concentration by volume and freezing point in degrees Fahrenheit.
-
T1000-9 -
Tesuto Systems
T1000-9 breakout box is our most compact breakout box, using dual 9 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 18 test points plus a ground jack. All test points use standard size 4mm banana jacks. Ideal for continuity testing, isolation testing or signal capture and monitoring.
-
NX Pro+ -
Dynalab Test Systems, Inc.
The Dynalab NX Pro+ Wire HarnessTester is modular and is designed for applications requiring up to 32,768 test points. It has the same front end as the NX Pro Tester, but employs a series of Expansion Units to accommodate the test point cards. Testing for continuity, shorts, and a variety of components. Highly flexible and adaptable product line that meets the changing needs of wire harness manufacturers.
-
Nidec-Read Corporation
In addition to jigs and fixtures for probing conductors and electrode pads, NIDEC-READ provides specialized software for test point selection and log analysis.
-
Model 3540 -
Epsilon Technology Corp.
Widely used for measuring deformations in three and four point bend tests, compression tests and a variety of general purpose deformations. These strain gaged devices come with a magnetic base for easy mounting.
-
Jinan Testing Equipment IE Corporation
Widely used for measuring deformance in three and four point bend tests, compression tests and a variety of general purpose deformations. These strain gaged devices come with a magnetic base for easy mounting.
-
Benz Co., Inc.
Tensile tests are used to determine how materials will behave under tension load. In a simple tensile test, a sample is typically pulled to its breaking point to determine the ultimate tensile strength of the material.
-
Tektronix, Inc.
A high voltage differential probe is used for measuring the voltage difference between two test points where neither test point is at ground. High voltage differential probes from Tektronix can be used for signals up to 6000 V. These probes are the best choice for making non-ground referenced, floating or isolated measurements in large part due to their common mode rejection capability. These products are designed, manufactured, and serviced by Tektronix.
-
XILS In-Line Handling Solutions -
EIIT, S.A.
Designed to cover a large number of test points, with long panels for future expansion, the XILS series of Handlers, PCB test systems in the line of EIIT - Innovative Engineering Solutions, is ready for the most demanding applications.
-
Mensor Corp.
Test pumps serve as pressure generators for the testing, adjustment and calibration of mechanical and electronic pressure measuring instruments through comparative measurements. These pressure tests can take place in the laboratory or workshop, or on site at the measuring point.
-
AMETEK Sensors, Test & Calibration
We supply a wide range of deflection gauge extensometers ideal for measuring deformation in three and four point bend tests and in compression testing applications.